Are you curious as to how skateboards stay balanced and rolling? If so, then chances are that you have wondered which way bearings go in a skateboard.
While this appears to be a simple enough question, the answer is actually quite complicated.
There’s more to setting up your bearings than simply inserting them into a wheel – there are several details that must be taken into account in order for your skateboard to remain durable and functional.
In this guide, we will discuss everything from what directions bearings should face when inserted, how often they need to be replaced and more. With the right knowledge on hand, you can ensure maximum efficiency while riding.
Quick Answer: Most skateboard bearings have one side with a colored shield. This side should face out when you install the bearings. If the bearing has one metal side and one plastic side (the dust guard), the plastic side should face outward and the metal side should be on the inside.
How do I know which way my bearings go in my skateboard?
Knowing how to properly put your bearings in your skateboard is a key element in the sport.
As you can now see, understanding which way your bearings should go and how to install them isn’t all that difficult.
Both the skateboard and bearings need to line up correctly so that proper alignment can be achieved.
So, if you’re looking to get out and hit the streets on a new board, just make sure you don’t forget the importance of having the right bearings.
Not only will it make sure your skateboarding experience is fun and smooth, but it will also help prevent any serious injuries should something go wrong due to improper installations.
Be sure to ask professionals for assistance if needed as safety must always be kept in mind when playing sports like skateboarding.
Enjoy your time on wheels, stay safe and let the good times roll.
Does it matter which way my bearings go in?
Yes, the orientation of bearings can matter depending on their type. For example:
- Tapered Roller Bearings: These bearings must be installed in a specific way. The larger end (the end with the larger raceway diameter) should face the direction from which the load is coming.
- Thrust Bearings: These are designed to handle axial loads and must be installed facing the right direction to effectively handle these loads.
- Radial Ball Bearings: These are typically symmetrical and can be installed in any direction.
However, it’s always best to check the manufacturer’s instructions when installing bearings. Incorrect installation can lead to premature failure or damage to the bearing and associated components.
How do I put my bearings in my skateboard?
One of the most critical aspects of skateboard maintenance is putting bearings on your skateboard.
Step 1: To start, you will need to gather the following materials:
- Your skateboard
- A set of bearings (8 in total – 2 per wheel)
- A skate tool
Step 2: Remove the wheels from your skateboard.
Place the screwdriver edge of your skate tool into the hole of the axle and push down while twisting the tool counterclockwise. Turn the screwdriver until the nut that holds the wheel in place comes off. Remove the wheel from the axle and repeat the process for the other three wheels.
Step 3: Remove the bearings from the wheels.
You can do this by using the tip of your skate tool to poke the bearing out of the wheel. Repeat this step for all eight bearings.
Step 4: Clean your bearings.
Place the bearings in a bowl and fill it with a cleaning solution such as citrus cleaner or rubbing alcohol. Swish the bearings around in the solution for about three minutes. Remove the bearings from the cleaning solution and dry them using a clean rag.
Step 5: Grease your bearings.
You can do this by applying a small amount of bearing grease or oil to the inside of the bearings. Rotate the bearings as you apply the grease, ensuring that they are well-lubricated.
- Do not use too much grease as this can attract dirt and debris.
- Do not use WD-40 as it will break down the lubrication properties of the grease.
Step 6: Insert your bearings into the wheels.
You can do this by using the axle of your skateboard by firmly pressing them into the slot in the center of the wheel. Repeat this for all eight bearings and four wheels.
- Make sure that each bearing is firmly in place before moving on to the next one.
- Make sure that the metal shield of the bearing is facing outwards when you insert it into the wheel.
Step 7: Put the wheels back onto your skateboard.
Line up the holes in the wheel with the axle of your skateboard, and push the wheel onto the axle while holding the bearing in place. Use your skate tool to tighten the nut that holds the wheel in place. Repeat this process for all four wheels.
- Make sure that the nut is tightened properly, but not so tight that the wheel cannot spin.
- Make sure that the bearings are facing each other, and not both facing the outside or inside of the wheel.
What are some tips for changing my bearings?
Here are some general tips for changing your bearings:
- Bearing Puller: This tool is used to remove bearings from the skateboard wheels.
- Skate Tool or Wrench: To remove the nuts on your skateboard wheels.
- New Bearings: Ensure that you have the correct size and type for your skateboard.
- Lubricant: It helps in reducing friction and extends the life of your bearings.
- Cleaning Materials: Rags or paper towels for cleaning off old grease or dirt.
Remove Wheels from Skateboard
- Loosen the Nut: Use your skate tool or wrench to loosen and remove the nut holding your wheel.
- Pull Off the Wheel: Once the nut is removed, pull off the wheel from the axle.
- Repeat Process: Do this for all four wheels.
Remove Bearings from Wheels
- Insert Axle into Bearing: Push the wheel’s bearing onto the axle of your skateboard.
- Apply Pressure: Tilt the wheel and apply pressure to pop out the bearing.
- Repeat for Other Side: Flip the wheel and repeat to remove the second bearing.
Clean and Lubricate New Bearings
- Remove Rubber Shield: If possible, remove the rubber shield from your new bearings for cleaning.
- Clean Bearings: Use a rag or paper towel to remove any dirt or old lubricant.
- Apply Lubricant: Apply a small amount of lubricant to the bearings.
Install New Bearings
- Place Bearing: Place one bearing on the axle of your skateboard.
- Push Wheel Onto Bearing: Push your wheel down onto the bearing until it pops into place.
- Install Second Bearing: Flip the wheel and repeat the process with the second bearing.
Remember to always follow the manufacturer’s instructions when changing your bearings. Different types of skateboards may require slightly different processes.